5.2.8. Electric knots of system of injection
AIR STREAM MEASURING INSTRUMENT
| PERFORMANCE ORDER |
|
1. Switch off ignition and disconnect the electric socket from the air stream measuring instrument (shooters specified collars of fastening of the measuring instrument of a stream of air). |
| 2. Weaken collars, exempt the air stream measuring instrument from inlet channels and remove it. |
| 3. Installation is made in the sequence, the return to removal. |
|
AIR TEMPERATURE SENSOR
Prevention
On turbo engines with high pressure the sensor of air temperature is an air stream measuring instrument component.
| PERFORMANCE ORDER |
| 1. Switch off ignition, disconnect the electric socket and take the sensor from the inlet channel. |
| 2. Installation is made in the sequence, the return to removal. |
|
SENSOR OF PROVISION OF THE PEDAL OF THE ACCELERATOR
| PERFORMANCE ORDER |
| 1. In interior of the car unscrew clips and remove finishing of the lower part of the dashboard from the driver. |
| 2. Disconnect the electric socket from the sensor which is located on the top part of a pedal. |
| 3. Remove a bracket of the spherical hinge of draft and remove draft from the sensor. |
|
4. Unscrew screws and remove the sensor from a pedal arm. |
| 5. Installation is made in the sequence, the return to removal. |
|
SENSOR OF THE BENT SHAFT
| PERFORMANCE ORDER |
| 1. Unscrew screws and remove a plastic casing from the top part of a head of the block of cylinders. |
| 2. For access to the sensor lift a forward part of the car and record on supports. |
|
3. Disconnect the electric socket of the sensor from a plait of wires. |
|
4. Unscrew a bolt and remove the sensor (it is specified by an arrow) from the block of cylinders. |
| 5. Installation is made in the sequence, the return to removal, at the same time it is necessary to install a new sealing ring on the sensor. |
|
SENSOR OF TEMPERATURE OF COOLING LIQUID
The sensor is installed from the forward right side of a head of the block of cylinders.
SENSOR OF EXCESS OF PRESSURE
| PERFORMANCE ORDER |
| 1. Unscrew screws and remove a plastic casing from the top part of a head of the block of cylinders. |
|
2. Unscrew the screws fixing an arm of a plait of wires to the top part of an inlet collector and disconnect the electric socket (it is specified by an arrow) from the sensor of excess of pressure. |
| 3. Unscrew a bolt and remove the sensor from the top part of an inlet collector. |
| 4. Installation is made in the sequence, the return to removal, at the same time it is necessary to install a new sealing ring on the sensor. |
|
OIL TEMPERATURE SENSOR
| PERFORMANCE ORDER |
| 1. Lift a forward part of the car and record on supports. |
| 2. Merge engine oil. Establish a new sealing ring on a masloslivny stopper and screw up it in the oil pallet. |
|
3. Disconnect the electric socket and unscrew the sensor from a forward part of the oil pallet. |
| 4. Installation is made in the sequence, the return to removal. Fill in engine oil in the engine. |
|
ELECTRONIC CONTROL DEVICE (ECU)
| PERFORMANCE ORDER |
| 1. Remove levers of screen wipers and remove a weight wire from the accumulator. |
| 2. Unscrew plastic nuts from axes of levers of screen wipers. |
| 3. Remove rubber consolidation from the top part of a partition of a motor compartment. |
| 4. Remove a plastic casing from the windshield basis. |
| 5. Unscrew nuts and remove the protection cover of the ECU block. |
| 6. Release clamps and disconnect the electric socket from the ECU block. |
| 7. Unscrew nuts and remove the ECU block. |
| 8. Installation is made in the sequence, the return to removal. |
|
